Use your drum for controlled pouring
Greatly reduce dust when discharging dry material
Quickly start and stop dispensing with slide gate
or iris valve
Extend the reach of pour
Drum
Cone
Model # 5SS-VF-90-23
Stainless Steel Asymmetric Drum Cone
Use
Drum Cones and Clamp Collars to control
dispensing of dry material from drum
Centered
Drum Cones
•
Mobile or Forklift Drum Handlers:
Centered
Drum Cones are ideal for use with various
mobile and forklift drum handlers, such as Vertical-Lift
Drum Pourers, HydraLift Karriers and Forklift
-Karriers.
Replace
your drum lid with a properly sized Drum Cone
and Clamp Collar to control dispensing operation by
turning your drum into a precise pouring instrument.
Add a Fork-Lift Karrier or Vertical-Lift Drum Pourer
and you’re ready to pour. Drum Cones are designed for
controlled dispensing of dry powdered or granulated
material and to reduce dust while discharging. Dispensing
can be stopped almost instantly with a slide gate or iris
valve. Attaching a drum cone to your drum extends the
reach of the pour by up to 15.5". This can be critical
when you need to reach beyond obstructions at the
receiving container.
•
Standard Kontrol-Karriers lack sufficient clearance
within the frame for a centered drum cone.
Cone
size # 23 fits drum
rim of 23-3/8" (59.4 cm)
outside diameter.
The
Drum Cones have a 6" (15.24 cm) discharge
opening, and are available for standard 30 and
55-gallon (114 and 210 liter) steel drums, and various
diameter fiber drums. Specify 45°, 60° angle, or
asymmetric drum cone. Choose cone made of carbon
steel, or finished type 304 stainless steel. 45° and 60°
carbon steel cones for 55-gallon (210 liter) drum
are seamless.
Asymmetric
Drum Cones
•
Only Asymmetric (off-center) Drum Cones can be
used with standard Kontrol-Karriers.
All
other sizes, and asymmetric and all stainless steel
cones are welded. Welds are not ground or polished.
Each cone has a neoprene gasket on the flange that
comes in contact with the drum rim. Carbon steel cone
interior is treated with a rust inhibitor.
Drum
Cones with valve flange allow you to
attach an Iris Valve or Slide Gate
Install
aluminum bodied Iris Valve Kit # IV for
controlling the flow of fine and coarse materials.
The operator revolves the handle around the valve
to open and close the flexible sleeve. A wide range
of fine to coarse materials can be handled without
clogging the iris valve
Recommended
for powdered material, but NOT for coarse
granulated products.
Model
XT - 5" (12.7 cm) Extension Tube Model XT-SS (not shown) also available - 5" Stainless
Steel
Extension Tube Note: Extension Tubes ONLY fit onto a valve flange or
an Iris
Valve. They are NOT for use with a Slide Gate Valve.
Shown
here with:
Asymmetric Drum Cone - Model 5-VF-90-23
Clamp Collar to secure cone to drum - Model 7-23
Iris Valve to control material flow - Model IV
Clamp
Collars to secure the Drum Cone to your drum
Order
a Clamp Collar to secure the cone
in position onto the top of your drum.
When ordering cones or clamp collars,
please specify the outside diameter of
the top drum rim. Remove the drum lid
and take several measurements across
the rim at various points and calculate the
average. See selection guide below.
Tighten
the Clamp Collar around the top rim of drum with the Drum
Cone in place. On the inside of the Clamp Collar there are sections
of steel rod to retain the Drum Cone, and sections of angle
iron to
engage under the drum top rim. Tighten the Clamp Collar by turning
the knob on the end of the threaded rod.
Selection
Guide for Drum Cones & Matching Clamp Collars
The following
6 steps correspond to information in the chart below.
(1) Cone Material: Choose stainless steel (SS) or regular steel
(2) VF = Valve Flange
(3) Angle of Cone: Choose 45° or 60° based on flow characteristics
of material
in your drum and height
restrictions within your application. Choose 90°
for Asymmetric drum cones with off-center
6" discharge opening.
(4) Size #: Determine Cone Size #
A. Identify drum type (steel or
fiber)
B. Measure the top rim outside diameter
of your drum
I. Remove
your drum lid before measuring
II. Measure
outside diameter across the rim at several points
III. Calculate
the average rim outside diameter
C. Select the Cone Size # for your
drum type and rim diameter
(5) Collar Material: Choose stainless steel (SS) or regular
steel
(6) Size #: Select Size # corresponding to the Size # of your
cone
KIT:
5" LONG x 6" DIAMETER STAINLESS EXTENSION TUBE.
ATTACH TO IRIS VALVE OR VALVE FLANGE. WELDS NOT GROUND
OR POLISHED. DOES NOT FIT SLIDE GATE.
5lb.
$491
Drum Cones &
Clamp Collars, Controlled Dispensing, Slide Gate or Iris Valve,
Drum Cone with Slide Gate, Iris Valve, Dispensing
of dry material from Drum, use your Drum for Controlled Pouring,
controlled Dispensing of dry Powdered or Granulated materials,
and Clamp Collars secure the Cone to your Drum from your source
for material handling equipment.
Use your drum for controlled pouring
