Blind
corner intersections are a prime spot for accidents in any industrial
setting – accidents that can result in
damage to equipment, the facility and most importantly to people.
Collision Sentry Corner Pro works to
prevent accidents at blind corners by sending both an audio
and visual alert to warn of approaching traffic.
Collision Sentry Corner Pro helps create a safer working environment
in areas where forklift traffic and
pedestrian traffic intersect.
Collision Sentry Collision Pro
Blind
corners and intersections are a common hazard in most industrial
settings. The Collision Sentry Corner Pro warning system helps
lessen
these hazards.
The addition of the Collision Sentry
Corner Pro system can:
• Protect people from injury
• Prevent equipment damage
• Prevent damage to the facility
• Increase and maintain productivity by avoiding delays
due to accidents
The
Collision Sentry Corner Pro sends a warning
ONLY when it senses movement in both detection
zones; motion on both sides of the blind corner.
Under
those conditions, the Collision Sentry Corner
Pro flashes in both directions and sounds an audible
warning, providing enough time for corrective action.
Detection
Zone
The
Collision Sentry Advantage
Audio
Warning
• Loud enough to be heard within the corner zone; pitch
sets it apart from
other background noise
• Volume can be adjusted (high/low) or turned off
• Sounds ONLY when motion is detected on both sides of
the corner
• Synchronized with light flash to reinforce warning
Visual Warning
• Flashes ONLY when motion is detected on both sides of
the corner
• LED lights angled; increasing light's intensity and optimizing
visibility
• Beam focused toward areas where it is best seen
• Lens concentrates and increases beam’s intensity
Simple Installation (see below for installation instructions)
• Deploys immediately, portable, compact and lightweight
• Integrated, recessed magnet mounts easily "snap
on" to racking,
maintaining a secure, tight fit.
• Integrated mounting points for mounting the unit to non-magnetic
surfaces
• Optimal installation height is 7-9 feet on the upright
Passive Infrared Motion Sensors
• Detection zone 20-25" in each direction
• Alert sent in ample time to take corrective action
• Pre-set and ready to use
Self-Powered
• Standard D-cell batteries (included)
• Blue light, beeping low battery indicator
• Battery life depends on usage, but lasts a minimum of
12 months
Order Online
Click the button of the item you wish to purchase.
Inspect
your product for any visible signs of damage.
To
activate the Collision Sentry Corner Pro, pull out the plastic
battery
tab located inside the unit. Remove the door on the front of
the unit,
pull the tab and replace the door. This activates the three
(3) "D" cell
batteries that are included with each unit. The LED lights will
begin
blinking as the device becomes oriented to the environment.
During
this warm-up period, the blue low battery indicator also flashes.
Note: Always activate the unit prior to installation. Pull
the tab, close the
door and the install the unit to the upright.
The
ideal placement for the unit is at a height between 7' and 9'
(2-2.75 m). Install with the mounting tabs at the top.
Use
the integrated magnets on the back to "snap" the unit
to a metallic
corner or rack.
The
included nylon tether provides extra security when mounting
the unit
using the magnets. Using the tether is optional but recommended.
Use
the integrated mounting tabs to install the unit directly to
nonmetallic
surfaces.
The
product needs about 20 seconds to acclimate to the new environment
and "learn" its new surroundings. During this warm-up,
the warning lights
will flash. The lights will go solid red for four seconds at
the end of the
warm-up period. This indicates the product is ready to use.
Collision
Sentry Corner Pro ships with the audio alarm activated
and set to the highest volume. This alarm can be adjusted using
the
switches found inside the unit and located below the battery
compartment. (See illustration). There are two switches used
for
adjusting the volume – a high/low switch and an off/on
switch.
1. Remove the door on the front of the unit.
2. Alarm switches are located below the battery compartment.
3. Adjust the switches to the desired setting.
4. Reinstall battery door.
5. Unit is now ready for use.
Collision Sentry,
Collision Warning System, Forklift Collision Detection, Forklift
Collision Avoidance, Column Protectors,
Commercial Railing, Folding Gates, Guard Rails, Guardrail,
Machine Guards, Rail, Protective Guards, Railing, and Traffic
Barricade from your source for material handling equipment.
