Back to Product Page
CONCRETE
SQUARE 4 SEAT TABLE
|
|
|
![](images/model_no_click_yellow.gif) |
|
Order
Online, by Phone, or by E-Mail |
|
|
|
~
Add items to your online shopping cart ~
Click the Model No. of the item
you wish to purchase.
|
|
|
![concrete square 4 seat table](images/concrete_square_table.jpg) |
|
Simple
lines and colors make these tables
an excellent choice for an outdoor café or
park area. High quality, low maintenance. |
|
|
|
Accepts
umbrella, without extra stand.
Assembly required. Also available in
ADA version as well as 2 seat version. |
|
|
|
ALSO--REFINISHING
KIT: TF3315
Make your table look NEW!! All the
materials you need to refinish your concrete
tables, benches, and seats to restore them
to like new condition. |
|
|
|
Size:
64" Sq. x 30" H installed
Weight: 1100 lbs.
Seating Capacity: 8 persons
Material: Reinforced concrete
Reinforcing: 1/4 & 3/8" Dia. steel rebar |
|
|
|
|
|
|
|
|
|
REFINISHING
KIT:TF3315 |
PRICE:
$1,900.00
|
|
|
PRICE:
$198.50 |
|
|
|
|
|
|
|
|
|
|
|
|
|
Hardware:
(1) - table-to-leg bracket |
|
Anchoring:
(4) - 3/8" x 1-1/2" inserts
(angle-brackets not provided)
Standard: (1) - 1-9/16" Dia. x 2" pop-out
plug in table top for umbrella pole
Assembly: Do not over tighten bolts or
inserts will pull out.
Maintenance: Periodically rinse with
water and mild detergent. Reseal
annually.
Packaging: Packaged unassembled in
crate, and shrink wrapped in plastic. |
|
(8)
- seat-to-leg brackets
(8) - 3/8" Dia. x 5 1/2" hex screws
(8) - 3/8" locking hex nuts.
(16) - 3/8 x 7/8 O.D S/S F/W
(4) - Neoprene Pads
(24) - 3/8" Dia. x 1-1/4" hex flange screws
(1) - 1/8 x 3 Keeper Pin |
|
Frame
(legs): (1) - top interlocking leg |
|
|
|
(1)
- bottom interlocking leg |
|
Top:
(1) - top 36" Sq. x 2"
Benches: (2) - benches 36" L x 12" W x 2"
H |
|
|
|
|
|
|
|
|
|
|
|
|
|
Available
Colors
|
|
|
|
|
|
|
|
![](images/acid_wash_sand_legs.jpg) |
|
![](images/acid_wash_gray_legs.jpg) |
|
Refinishing
Ground & Polished Concrete Instructions
|
|
|
|
|
|
|
|
Kit
Includes: |
|
|
|
![](images/refinishing_kit.jpg) |
|
-
2 lbs Grout Mixture
- 10 oz Bonding Agent
- 4 Spray Cans of Sealer |
|
|
|
|
|
|
|
|
|
Additional
Items Needed: |
|
|
|
-
Rubber Gloves
- #240 Sand Paper
- Sanding Block
- Mixing Tool
- Scrubbing Pad |
-
#80 Grit Sand Paper
- Pail
- Sponge
- Squeegee |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Note:
Wear rubber gloves during entire refinishing process. Refinishing
results are best
when all excess grout is removed and surface is sanded smooth.
Check for and clean up
spills after each step. Newly refinished tables will retain
an attractive appearance for
several years if they are resealed at least once a year. |
|
|
|
![](images/refinishing_instruction_pic_1.jpg) |
|
![](images/refinishing_instruction_pic_2.jpg) |
|
1.
Scrub and Rinse
Rinse surface with water while using scrubbing pad to
remove dirt and grime. Using the sanding block and
#80 sand paper, sand surface. Repeat rinse. |
|
2.
Grout
Mix grout and bonding agent together to create
a creamy consistency in a pail. Allow to set for
5 minutes Apply to the surface using a circular
motion, with a sponge to fill all voids. Can
be used on smooth edges, not on acid wash
surfaces. |
|
|
|
|
|
|
Note:
Acid wash edges to be taped off before groutin
the surface to avoid getting grout in pores of edge. |
|
|
|
![](images/refinishing_instruction_pic_3.jpg) |
|
3.
Remove Excess Grout
Immediately remove all excess grout with a squeegee.
Apply water as needed to keep grout moist with a spray
bottle. Thoroughly inspect the surface to be certain it is
clean. Allow to cure for approximately 24 hours. |
4.
Wet-Sand
Once the surface has cured, wet-sand grouted
surface using sanding block, #240 sandpaper
and water. |
|
|
|
|
|
|
|
![](images/refinishing_instruction_pic_4.jpg) |
|
5.
Clean
Thoroughly rinse with water and allow to dry. Surface
must be dust free. If tape was needed for edges
remove tape before cleaning the surface. |
|
4.
Wet-Sand
Once the surface has cured, wet-sand grouted
surface using sanding block, #240 sandpaper
and water. |
|
|
SPECIFICATION
|
|
|
|
1.1
SUMMARY
A. Section includes: Furnish Precast Concrete Table
indicated on drawings or
specified herein.
1.2 REFERENCES
A. American Society for Testing & Materials
1. ASTM C33 2.
ASTM C150 3. ASTM C31 |
|
1.6
QUALITY ASSURANCE
A. Qualifications of Manufacturer: Manufacturer
to be pre-qualified by
specifier prior to
bidding. Failure to comply
will result in
disqualification of bid.
Manufacturer to have
at least five years experience
in the manufacturer
of precast concrete
tables field proven for at
least five years. |
1.5
SUBMITTALS
A. Submit product data, shop drawings and
Samples.
1. Product Data: Manufacturer's
specifications
and technical
data edited specifically for
proposed system,
including the following
specific information:
a. Detailed
specification of construction
fabrication.
b. Manufacturer's
installation instructions
c. Maintenance
literature
d. Product
warranty
2. Shop Drawings: Indicate
pertinent dimensions,
general
construction, component connections
anchoring
methods, hardware and installation
procedures.
3. Samples as requested
by Architect. |
|
|
1.10
WARRANTY
Manufacturer shall submit a written warranty
for
precast products for the period of two years
upon
acceptance of products. |
|
2.2
MATERIALS
A. Portland Cement: ASTM C150 specifications
for Portland Cement.
B. Aggregates: All aggregates to meet ASTM C33
specifications, to be cleaned
of foreign matter
and properly graded to size.
C. Coloring: Pigments used shall be inorganic,
resistant to alkalinity
and used as per
manufacturers recommendations. |
|
|
|
![](images/diagram.jpg) |
|
Concrete Square
Table, Picnic Tables, Concrete Tables, Park Furnishings, Tables,
Site Amenities, Site Furnishings, and
Street Furniture from your source for material handling equipment.
|
Back to Product Page
|
HOME /
ORDER / SEARCH
/
QUOTE /
CONTACT US / ABOUT
US /
MY ACCOUNT/
SHOPPING CART |
|