Back to Product Page
|
|
|
|
Order
Online, by Phone, or by E-Mail |
|
|
|
~
Add items to your online shopping cart ~
Click a Model No. of the item
you wish to purchase.
|
|
|
|
PRICING
FOR MODEL 77 - BALE LIFTING TONGS
|
Model
No. |
Rated Cap.
In Tons |
Bail
Width |
Unit Height
Loaded |
Pad
Dim's |
Weight
Lbs. |
Price |
Width |
Height |
77-1/2-36 |
1/2 |
36 |
52 |
18 |
9 |
280 |
$10,655
|
77-1/2-48 |
1/2 |
48 |
56 |
18 |
9 |
300 |
$11,158
|
77-1-36 |
1 |
36 |
52 |
18 |
9 |
280 |
$11,345
|
77-1-48 |
1 |
48 |
56 |
18 |
9 |
300 |
$11,835
|
|
|
|
|
|
|
|
|
GENERAL
INFORMATION:
|
|
|
|
|
|
|
|
|
|
Lifting Tongs are designed and manufactured to customer
load specifications. Optional is an automatic latching device. |
|
|
|
|
|
|
All
Lifting Tongs are designed and manufactured to
conform with ASME B30.20 standards. |
|
|
|
|
|
|
|
|
|
|
Lifting
tongs are available in three configurations.
|
|
|
|
|
|
|
|
|
|
1.
GRIPPING - Grab arms conform to load surface with outside
diameter supported below center of load for
additional holding
advantage. |
|
|
|
|
|
|
|
|
|
Designed
to lift such products as rolls, tubes, and other
cylindrical materials. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2.
PRESSURE - Grab arms grip vertical sides of straight sided
materials. Custom grip pads are required
to have sufficient
coefficient of friction between material
lifted and grip pads. Grip
pads may be rubber, steel, belting, points
and other. |
|
|
|
|
|
|
|
Designed
to lift such products as bales, boxes, ingots, and
other straight sided materials. |
|
|
|
|
|
|
|
Standard
tongs for bales and slabs are shown above and also
see Model 71 - Slab Tongs section. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3.
SUPPORTING - Grab arms have feet to support underneath load.
Designed to handle constant sizes of material
to maintain a
horizontal plane on the lifting feel. Dunage
under material required
to insert/remove feet of tong. |
|
|
|
|
|
|
|
|
|
Designed
to lift constant sized boxes, containers, crates, and
other constant sized square shaped material. |
|
|
|
|
|
|
|
|
|
Standard
Tongs for dies see Model 70 - Die Lifting Tongs section. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Application
Ideas for Gripping Tongs... |
|
|
|
|
|
|
|
|
|
|
|
|
to
lift rolls, tubes, and cylindrical materials |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
This
GRIPPING TONG is used to lift cylindrical objects
such as large diameter round bar, tube or rolls of material. |
|
|
|
|
|
|
|
|
|
|
|
|
We
have integrated both a manual latch or the autolatch
mechanism into this family of tongs. The selection of the
latch is dependent on the application. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
This
GRIPPING TONG is designed to handle longer loads
and loads that may be more susceptible to damage. The
longer contoured pads used on the tong arms even the
pressure on the lifted item. This would be useful when lifting
rolls of fabric or polyethylene film. The pads could be lined
with a material such as nylon or rubber and used to lift brass
bar or machined parts without the potential for damage that
may occur if using slings or forklifts. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
This
GRIPPING TONG is designed to pick up long lengths
of round bar or bundles of steel that are approximately
round in shape. The narrow gripping arm will engage the
lifted item with significant pressure. |
|
|
|
|
|
|
|
Lifting Tong,
Lifting Tongs, Bale Lifting Tong, and Bale Lifting Tongs from
your complete source for material handling equipment.
|
Back to Product Page
|